One Sturdy Rubber Thrusting Tip- Your choice of Low Profile or Two Handed Sword This goodly Rubber Thrusting Tip designed is specifically made for SCA and heavy combat. Made of a sturdy vulcanized rubber it is tough and presents a neat finished appearance to your sword with a single piece stout injection molded construction. These have been designed to be deliver a telling blow while at the same time have an inner crush space supported by high quality EVA foam that moderates the severity of the blow for the safety of the recipient. These designs are widely accepted through the Known Worlde and most Kingdoms so can help a weapon pass inspection more quickly. Please check with your marshal to confirm compliance with your area. There are two varieties: The Low Profile/Single hand sword tip measures 2 1/2″ long x 1 1/2″ wide (outside diameter) across the thrusting surface. Included 2 foam discs for rules compliance (see *1 below for citation). This is intended to fit a stick of rattan of about 1 1/4″ in diameter or perhaps just a bit larger (since it is made of rubber). Don’t be crazy and shove a too huge stick in! At only 1 1/4 ounces, this is a superior solution for installing onto your single sword.The Two Handed Sword Tip measures 3 3/4″ long x 2″ wide (outside diameter) across the thrusting surface. Included 6 foam discs for rules compliance (see *2 below for citation). This is intended to fit a stick of rattan of about 1 1/2″ in diameter or perhaps just a bit larger. And yes, this is not something you will shove a too huge stick into! At just under 4 ounces, this is a robust and well designed tool for delivering a positive yet safe thrust kill with your great sword.In appearance, they are a mostly smooth black surface. They’re specifically designed and manufactured for SCA combat, with a large dollar investment and many hours invested in design, mold costs, and prototype runs. If you haven’t seen one, you haven’t seen anything like it. Rules Citation: *1 Low Profile Thrusting Tips are the same diameter as the sword they are mounted on. They must be constructed of at least 1 1/4 inches (33mm)of closed-cell foam (although at least 1 1/2 inches (38mm) is recommended). The thrusting tip will be securely attached with at least 1/2 inch (12.5mm) of progressive give across the face of the thrusting tip without allowing contact with the rigid tip of the weapon….This type of trusting tip may be only used for single-handed weapons and it must be marked with contrasting tape.” -Marshals Standards as they are published on SCA.org Our low profile thrusting tips have been approved for use at the Society level and for use within the following kingdoms: Atenveldt, Caid, Meridies, Calontir, Outlands, East, Northshield . ( *2 “…They shall be no less then 2” (51 mm) in diameter or cross section and shall provide progressively resistant “give” under pressure without allowing contact with the rigid tip of the weapon. It shall not be possible to force the guard more then 1/2″ (12.5 mm)into a legal face guard.” -Marshals Standards as they are published on SCA.org Assembly Instructions: ( Sent with each tip but you will always have a copy here to refer to even if you ditch the packaging)Insert some discs of foam into the inside of your new Thrusting Tip.Cut your rattan stave to a 90 degree angle and round the edge according to SCA rules. Place the tip onto the rattan and test for give.Evaluate the ‘give’ of the tip. Add or remove foam to dial in the tips firmness.Affix the tip onto the rattan with one layer of glass filament tape running parallel to the length of the rattan. Note: There are lines on the outside of the tip. Tape to the Fourth line for our recommended construction. Be sure that the tape passes the edge of the tip and down the rattan several inches.Apply a second,layer of glass filament tape in a spiral over the first layer.Cover the filament tape with your choice of duct tape.Over time, the foam may deteriorate and need to be replaced. Satisfaction policy – Your happiness with our products is a top priority. See our feedback and know that this represents our sincere commitment to our customers. Please contact us if you have any problem with what we’ve sent. The deal’s not done till everyone leaves smiling. A note on handling time: We generally ship in just a few days. However there are periods in the armor cycle when we are at week long events or getting mobbed that it may take longer. We guarantee that your armor will be shipped in the time-line set in the auction if not sooner. Please let us know if you are in urgent need by a specific date and we’ll do our very best to accommodate your schedule. We guarantee lifetime satisfaction on all of our armor, HOWEVER we do not guarantee the life of the user. Any contact sport has the potential for bodily harm and injury, if using our products in a contact fighting, sparring or any other reenactment involving weapons we do not guarantee against injury! Custom works happily considered for belts, shields or body armor. For more detail on what we can do visit Dark Victory Armory on Facebook or the web. Best Regards and Thanks for Visiting!To See Our Latest Workshop Creations visit Dark Victory Armory on Facebook or the web.Our Sincere Thanks for Patronage, Jordan (and David), chief armorer (and apprentice) Dark Victory Armory and remember your purchase supports the Society for Feeding Ancient House Cats. Track Page Views With Auctiva’s FREE Counter

Sturdy Rubber Medieval Mace Head This auction is for a goodly Rubber Mace Head which are particularly useful for SCA and WMA heavy combat. Made of a heavy vulcanized rubber it is extremely tough and nearly indestructible given it’s single piece stout injection molded construction. These industrial quality heads can deliver a telling blow while at the same time having fins that moderate the severity of the blow for the safety of the recipient. This design has been specifically approved by the Society Earl Marshal for SCA combat in all Kingdoms as of 2010 and is widely accepted through the Known Worlde. However each Kingdom will have it’s own standards for weapon construction (particularly overall mass) so please consult with your marshals. Physical Size: The diameter across the prominent fins is 3 7/8″ (10 cm) across the striking surfaces and 2 7/8″ (7.3 cm) top to bottom. Shaft hole is 1 1/4″ (3.2 cm). Weight is just under 11oz. (300 grams). We now offer a COMPLETED Mace! We mount the head onto a 12″ or 20″ rattan shaft for you so it’s ready to fight right out of the package. We can mount the head onto our longer rattan combat staves (https://www.ebay.com/itm/Manau-Rattan-Sword-SCA-LARP-Armor-Combat-Stave-1-1-1-1-2-/270804539201 ) at no additional charge for that service. Just purchase a 1 1/4″- 1 1/2″ size and send a note to request a “long mace”. In appearance, they are a mostly smooth black surface with 8 prominent reinforced flanges interspersed with 8 smaller flanges.. This is an industrial product that has been re-purposed from it original use as an agricultural roller for handling sturdy root vegetables and applied to the activity of medieval combat. This is the reason that the price is so incredibly modest since the massive investment and many hours that would normally need to be spent on design, mold costs, and prototype runs are spread out over a MUCH larger customer base. So we all get a GREAT discount from this opportunity. If you haven’t seen one, you haven’t seen anything like it.Like any impact weapon, these are made to take a beating but they are not immortal. Feedback comment from a happy customer – “These are the bomb! They DO wear out, when you are whacking tires with them.”We offer the absolute best price on these. We consistently are the price leader and send a tracked shipment with blazing fast turnaround. Check our feedback! If these Mace Heads are of interest to you, perhaps you’d also like to get a look at our Rugged Hammer and Spear Heads! Find them here: https://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=121191557371&ssPageName=STRK:MESE:IT Satisfaction policy – Your happiness with our products is a top priority. See our feedback and know that this represents our sincere commitment to our customers. Please contact us if you have any problem with what we’ve sent. The deal’s not done till everyone leaves smiling. A note on handling time: We generally ship in just a few days. However there are periods in the armor cycle when we are at week long events or getting mobbed that it may take longer. We guarantee that your armor will be shipped in the time-line set in the auction if not sooner. Please let us know if you are in urgent need by a specific date and we’ll do our very best to accommodate your schedule. We guarantee lifetime satisfaction on all of our armor, HOWEVER we do not guarantee the life of the user. Any contact sport has the potential for bodily harm and injury, if using our products in a contact fighting, sparring or any other reenactment involving weapons we do not guarantee against injury! Custom works happily considered for belts, shields or body armor. For more detail on what we can do visit Dark Victory Armory on Facebook or the web. Best Regards and Thanks for Visiting! To See Our Latest Workshop Creations visit Dark Victory Armory on Facebook or the web.Our Sincere Thanks for Patronage, Jordan (and David), chief armorer (and apprentice) Dark Victory Armory and remember your purchase supports the Society for Feeding Ancient House Cats.

The rich brown leather construction showcases expert handcrafting with its overlapping scales and detailed stitching. Multiple adjustable belts at the waist ensure a secure, customizable fit. The versatile design works equally well for various character interpretations, from Roman legionaries to fantasy warriors.

The Ready For Battle Steel Arm Bracers is sold as a pair. Made from 18 gauge steel. It is a very strong material and comfortable to wear. Steel Gauge: 18G.

This product is made Elegant and simple; we have designed this German Landsknecht dress to show your natural beauty and enhance you in all of the right places. We were inspired by the 16th century when designing this dress.

NOTE: Stains Inside and Out – see Photos. Deep Blue Velvet Shell with Gold Satin Lining. Tatted with Gold/Pearl Trims. Outer Stain has NOT been Cleaned or Attempted at Cleaning. Inner Lining has Black Make-Up or Ink Stains and Multiple other Stain Marks – No Cleaning has been Attempted.

【Quality】The chest harness is made of premium quality faux PU leather material with feathers, comfortable and allows you to move freely. Ideal for Carnival, Easter, cosplay party, Halloween, or any other special occasion.

Ring Type : Flat Riveted Ring. Material : Mild Steel With Brass. Finish : Oil Finished.

Material : Mild Steel. Product Detail. Size: Standard Adult Size (Fits Almost All Adults).

The elegant brass dagged edge design adds a unique historical look, while the adjustable belt ensures a comfortable fit. Edge Design: Brass Dagged Edge. Material: Mild Steel. ✔ Decorative brass zig-zag edge.